Products

This is a translucent silicon rubber button pad with 16 buttons originally inspired by the folks at monome.org. Each button has a hole underneath t...

This is a CAN FD shield for the STM32G431 Nucleo-G431RB. It use the Microchip MCP2562FD CAN FD transceiver.  Features Microchip MCP2562FD C...

This is a CAN FD shield for the STM32H503RB Nucleo-H503RB. It use the Microchip MCP2562FD CAN FD transceiver.  Features Microchip MCP2562FD...

This is a CAN-Bus breakout board using Microchip's MCP2551 High Speed CAN Transceiver IC. The output pins are on both screw terminal and DB9 connec...

This is a high quality cable designed for Classic CAN and CAN FD operations. Available in 2/4/5/6/10m length. Features DB9 female connector at bot...

This is a CAN-Bus breakout board with Flexible Data Rate using the Microchip MCP2562FD chip. The output pins are on both screw terminal and D...

This is a CAN-Bus breakout board with Flexible Data Rate using the Microchip MCP2561FD chip. The output pins are on both screw terminal and ...

This is a CAN-Bus FeatherWing for use with the ESP32 board. It uses the SN65HVD231 CAN transceiver with a PESD1CAN ESD protection. Features ...

This is a 7 port CAN-bus hub with DC power distribution. A 120R terminator is on board with jumper enable option. Features 7 x CAN port 120R termi...

This board converts CAN-bus data into UART and vice versa. CAN and UART baud rate is programable via a CAN message. The UART has a standard pin...

This board converts CAN-bus data into UART and vice versa. CAN and UART baud rate is programable via a CAN message. The UART has a standard pin...

The CANgineBerry CANopen is an active CAN co-processor module that uses a regular UART communication channel towards the host system. With its inde...

The CANopenIA-M0 SoM implements the CANopen protocol compliant to the CiA standards. CANopenIA-M0 is based on the NXP Cortex M0 32-bit micro c...

CAN bus is a protocol used in hundreds of millions of devices including cars, trucks, buses, construction machines, ships, tractors, and spacecraft...

New version with Pico WH on socketed board. CAN bus is a protocol used in hundreds of millions of devices including cars, trucks, buses, constructi...

Add lots of touch sensors to your next microcontroller project with this easy-to-use 8-channel capacitive touch sensor breakout board, starring the...

sku: SEN-09403 This is a simple-to-use Carbon Monoxide (CO) sensor, suitable for sensing CO concentrations in the air. The MQ-7 can detect CO-gas c...

Cat5 UTP Cross Over cable 2m.

Cat5 UTP Patch Cable 4m (grey).

Cat5E UTP Patch Cable 2m (colour may vary).

For years we've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow, or...

sku: CEL-09607 The Cellular Shield for Arduino includes all the parts needed to interface your Arduino with an SM5100B cellular module. This allow...

#3333 Circuit Playground Express is the next step towards a perfect introduction to electronics and programming. We've taken the original Circuit P...

sku: PRT-00338 CR2032 Lithium Ion 3V 250mAh button cell battery. Great for powering low power processors or blink an LED for weeks at a time. Dimen...

sku: DEV-08822 This is a coin cell holder for the common CR2032 type battery. The holder has a neat pop-in, pop-out feature that makes changing th...

sku: LCD-08448 Description: This is a 4-wire resistive analog touch screen. Intended to mate with the 24-Bit PSP display, this unit comes with a h...

sku: BOB-09224 Description: This is the SMD connector for the PSP touch screen. 4-pin right angle good, friction fit connector with 1 mm pitch. D...

This is a very simple breakout board for the popular HMC6352. Remember the KISS mantra? We really enjoy the simplicity and ease of use with the HMC...

The HMC6343 is a solid-state compass module with tilt compensation from Honeywell. The HMC6343 has three axis of magneto, three axis of acceleromet...

sku: COM-09339 This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for ma...

sku: COM-09337 This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for ma...

sku: COM-09341 This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for ma...

sku: COM-09336 This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for ma...

sku: COM-09340 This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for ma...

sku: COM-09337 This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for ma...

"Conductive Temporary Hold" Similar to Vlcro but conductive. One inch wide(25mm). Excellent holding power and RF shielding. Use it to create re-s...