CAN Bus Boards

CAN bus is a protocol used in hundreds of millions of devices including cars, trucks, buses, construction machines, ships, tractors, and spacecraft...

New version with Pico WH on socketed board. CAN bus is a protocol used in hundreds of millions of devices including cars, trucks, buses, constructi...

This board has an ESP32 WROOM-32 WiFi, Bluetooth Classic and BLE Module and a CAN transceiver. On board is a RGB LED, IO pins on a 0.1" pads. P...

This cable is a DB9 female to a OBDII male with a flat cable.Features OBDII male DB9 female Flat cable Cable length : 1500mm Typical use on a CAN...

This is a CAN-Bus breakout board with Flexible Data Rate using the Microchip MCP2562FD chip. The output pins are on both screw terminal and D...

The jCOM.CAN.DUE, a dual CAN bus interface for the Arduino Due, is not an Arduino shield in the common sense. The board incorporates dual CAN tran...

This is a 7 port CAN-bus hub with DC power distribution. A 120R terminator is on board with jumper enable option. Features 7 x CAN port 120R termi...

The jCOM.J1939.USB gateway board is a high-performance, low-latency vehicle network adapter for SAE J1939 applications. It allows any host de...

This is a CAN FD shield for the STM32G431 Nucleo-G431RB. It use the Microchip MCP2562FD CAN FD transceiver.  Features Microchip MCP2562FD C...

The jCOM.CAN.DUE-X, a dual CAN bus interface for the Arduino Due, is not an Arduino shield in the common sense. The board incorporates dual CAN tr...

This is a CAN-Bus FeatherWing for use with the ESP32 board. It uses the SN65HVD231 CAN transceiver with a PESD1CAN ESD protection. Features ...

This is a breakout board with the Microchip MCP2518FD CAN FD controller and the MCP2562FD CAN Bus transceiver.  Features  Conforms to ISO1...

This is a two channel PT100 RTD to CAN-Bus converter. Based on the MAX31865 integrated circuit.  Features Two channels Compatible with 2-, ...

A moulded OBDII to DB9 female cable. Features 1500mm length Fully moulded with strain relief DB9 female connector with thumb screw WARNINGThe DB9...

This cable is a DB9 female to a M12 5way Micro C male connector. Features M12 5way Micro C male DB9 female Cable length : 1500mm Typical use ...

This is a CAN-Bus breakout board using Microchip's MCP2551 High Speed CAN Transceiver IC. The output pins are on both screw terminal and DB9 connec...

This is a CAN FD shield for the STM32H503RB Nucleo-H503RB. It use the Microchip MCP2562FD CAN FD transceiver.  Features Microchip MCP2562FD...

This board converts CAN-bus data into UART and vice versa. CAN and UART baud rate is programable via a CAN message. The UART has a standard pin...

This is a Microchip dsPIC33CK256MP502 CAN FD demonstration board. The micro-controller has 256kb flash and 24kb ram. It has on board CAN FD tran...

This board converts CAN-bus data into UART and vice versa. CAN and UART baud rate is programable via a CAN message. The UART has a standard pin...

This is a STM32G431 Nucleo board and a CAN-bus shield with two potentiometers, two push button switches and four LEDs. The STM32G431 board is pre-p...

The CANopenIA-M0 SoM implements the CANopen protocol compliant to the CiA standards. CANopenIA-M0 is based on the NXP Cortex M0 32-bit micro c...

This is a Curiosity Nano PIC18F57Q84 CAN FD Board. The Curiosity Nano is pre-installed onto the carrier board. The carrier board has a CAN FD t...

#4759 One of our favorite Feathers, the Feather M4 Express, gets a glow-up here with an upgrade to the SAME51 chipset which has built-in CAN bus su...