Products

sku: PRT-08484 If you need some juice, this 6Ahr triple pack is for you. These are very slim, extremely light weight batteries based on the new Pol...

These are very slim, extremely light weight batteries based on the new Polymer Lithium Ion chemistry. This is the highest energy density currently ...

PRT-11231  The PowerCell board is a single cell LiPo boost converter (to 3.3V and 5V) and micro-USB charger in one.  The board comes with a JST con...

Pack Content 1X Barrel jack adaptor-screw terminal to 2.1mm male 1X Barrel jack adpator-Screw pluggable terminal to 2.1mm male 1X Barrel jack ...

#2030PowerBoost is the perfect power supply for your power-hungry portable project! This little DC/DC boost converter module can run from 1.8V batt...

PowerBoost 1000C is the perfect power supply for your portable project! With a built-in load-sharing battery charger circuit, you'll be able to ke...

PowerBoost is the perfect power supply for your portable project! This little DC/DC boost converter module can run from 1.8V batteries or higher, a...

PowerBoost 500C is the perfect power supply for your portable project! With a built-in battery charger circuit, you'll be able to keep your project...

This board is an Arduino Pro Micro at 3.3v/8MHz with pre-soldered headers and firmware of AnyIO pre-loaded.AnyIO Firmware A GPIO Package that works...

      This is a metal case for use with the PiCAN2,3 and PiCAN FD board and the Raspberry Pi 4. Attached to the case is a DIN rail plate for mount ...

This adaptor consists of 2 boards connected via a ribbon cable. The connector on the smaller board fits into the programming connector of any Modtr...

sku: PRT-08723 We asked ourselves what we would want in a project board. What would an ideal platform for most any given project look like? After p...

sku: PRT-10614 We asked ourselves what we would want in a project board. What would an ideal platform for most any given project look like? After ...

DEV-11201  The ProtoSnap series is a new way to prototype your project without a breadboard. Everything is wired together on a single board, which ...

DEV-11032 The ProtoSnap series is a great way to prototype your project without a breadboard. Everything is wired together on a single board, which...

A single sided prototype board. The other side of the board are copper circles not strips. Features 7cm x 9 cm Power pads X and Y legends...

The PT66EI-24P is a prototype board for Netcruzer SBC66 Single Board Computers. The SBC66 board is plugged onto the PT66EI-24P board as a daug...

The PT24E is a prototype board. It has been designed for a MicroX SBC Main Board to be plugged onto it, and to fit in a ENC2015S enclosure. This bo...

The PT10E is a prototype board. It has been designed for a MicroX SBC Main Board to be plugged onto it, and to fit in a ENC2015S enclosure. This bo...

This is a 5v 2.5A PSU suitable for use with Raspberry Pi 2/3.Features Micro USB connector Input Voltage VAC: 100V AC to 240V AC Output Current: 2....

Compact Prototype frontend board, NO connector assembled. When fitted with header connectors, this board will plug into the Frontend Board Connector.

Compact Prototype frontend board, NO connector assembled. When fitted with header connectors, this board will plug into the daughter board connecto...

Compact Prototype daughter board, NO connector assembled. When fitted with header connectors, this board will plug into the daughter board connecto...

The QTR-1A reflectance sensor carries a single infrared LED and phototransistor pair in an inexpensive, tiny 0.5" x 0.3" module that can be mounted...

The QTR-1RC reflectance sensor carries a single infrared LED and phototransistor pair in an inexpensive, tiny 0.5" x 0.3" module that can be mounte...

This sensor module has 8 IR LED/phototransistor pairs mounted on a 0.375" pitch, making it a great detector for a line-following robot. Pairs of LE...

This is a fantastic find for SFE. A small, high-quality, quad-band, standard SMA terminated, cellular antenna. Specifications GSM/850E : 824 to 89...

A Quad-band antenna for embedded cellular devices. This antenna will allow you to connect your cellular module to the outside world. Operates on fo...

sku: ROB-10507 The Quadstepper motor driver board allows you to control up to 4 bipolar stepper motors simultaneously using logic level IO pins....

The Quick2Wire PCF8591 I2C Analogue Board has four 8­bit Analogue Inputs and one 8­bit Analogue Output. You can use the boards to measure four vol...

The Quick2Wire® I2C Port Expander kit connects to our Raspberry Pi Interface board and gives you 16 additional GPIO pins which you can configure as...

The Quick2Wire® Interface Board Kit gives you safe and easy access to all the features on your Raspberry Pi’s expansion header. The Board and its c...

This is a 100mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for o...

This is a 200mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for o...

#1590 Have you gazed longingly at large TFT displays - you know what I'm talking about here, 4", 5" or 7" TFTs with up to 800x480 pixels. Then you ...

This is a  kit of 4x4x4 RGB LEDs cube, containing 64 8mm RGB LEDs, custom PCBs and all supporting components  (6 free alternate LEDs included in ki...

This stackable 40-pin female header features two rows of 20 pins spaced with a standard 0.1″ (2.54 mm) pitch. This is used for extending the ...

The Raspberry Pi Model B+ is THE new favorite of development platforms, so the last thing that you’d want is for something bad to happen to it. Wh...

New Raspberry Pi 3 Model B+Features Broadcom BCM2837B0, Cortex-A53 (ARMv8) 64-bit SoC @ 1.4GHz 1GB LPDDR2 SDRAM 2.4GHz and 5GHz IEEE 802.11.b/g/n/a...

Raspberry Pi 4 Model B is the latest product in the popular Raspberry Pi range of computers. It offers ground-breaking increases in processor speed...

Raspberry Pi 4 Model B is the latest product in the popular Raspberry Pi range of computers. It offers ground-breaking increases in processor spee...

The 7" Touchscreen Monitor for Raspberry Pi gives users the ability to create all-in-one, integrated projects such as tablets, infotainment system...

The Raspberry Pi Camera Module v2 is a high quality 8 megapixel Sony IMX219 image sensor custom designed add-on board for Raspberry Pi, featur...

LIN (Local Interconnect Network) is a serial network protocol used for communication between components in vehicles. It is a single wire, serial ...

This is comprehensive electronic kit for the Raspberry Pi. It includes some advance IC such as the MCP3002 ADC and MCP4802 DAC. For measurement a T...

This a custom designed module for the DS1307 Real Time Clock. The module comes fully assembled and pre-programmed with the current time (ok, so it'...

Rectangular OBDII connector with blankend. Ideal for dongle use. Supplied with 16 pins.