Products

sku: BOB-10160 Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time ...

Mini Diagonal Cutters. These are great little cutters! A must have for clipping leads and extra solder tails. 4" long.

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow. Features Forward Voltage (R...

sku: TOL-09141 This is for all those starving students that need to buy their first good, low-cost multimeter. This meter has really impressive ov...

SEN-09418  This is a breakout board for the incredibly small TMP102 digital temperature sensor. The TMP102 is a digital sensor (I2C a.k.a. TWI), ha...

This is a 3-Pole DMX cable in 1m length manufactured by Pulse.Features LEAD, XLR DMX, 3P, 1M . Lead Length:1m Cable Type:DMX Colour:Black Connect...

This is a 3-Pole DMX cable in 3m length manufactured by Pulse.Features LEAD, XLR DMX, 3P, 3M . Lead Length:3m Cable Type:DMX Colour:Black Connect...

This is a 3-Pole DMX cable in 5m length manufactured by Pulse.Features LEAD, XLR DMX, 3P, 5M . Lead Length:5m Cable Type:DMX Colour:Black Connector...

This DMXduino is an open source hardware project. Based on the Arduino and with an Atmega328 micro-controller. It decodes the DMX signal and drive ...

Oof - you got a Raspberry Pi Model B+ that you want to have work with some old kit or plate or breakout or something and it uses the classic 26-pi...

Drawdio is an electronic pencil that lets you make music while you draw! It's great project for beginners: An easy soldering kit with instant grati...

Pololu item #: 2132The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver. The mo...

DS1307 I2C bus RTC chip, DIL08 package. Can be plugged into a socket on some Modtronix board to add a RTC. Real-time clock (RTC) counts seconds...

An oscilloscope is an awesome tool to have around the shop. Unfortunately, most scopes take up quite a bit of bench space and they're not very port...

DSO Quad – Aluminum Alloy now is available at Seeed Studio. A new, rigid, elegant aluminum alloy shell makes the Quad even better. This is the cool...

A dual 7-segment green LED display, 0.56" height. Common Anode. Features Type HDSP-521G LED DISPLAY, DUAL, 0.56", GREEN Operating Temperatur...

The jCOM.CAN.DUE, a dual CAN bus interface for the Arduino Due, is not an Arduino shield in the common sense. The board incorporates dual CAN tran...

The jCOM.CAN.DUE-X, a dual CAN bus interface for the Arduino Due, is not an Arduino shield in the common sense. The board incorporates dual CAN tr...

This dual brushed DC motor driver, based on Freescale's MC33926 full H-bridge, has a wide operating range of 5 - 28 V and can deliver almost 3 A co...

This is a two channel PT100 RTD to CAN-Bus converter. Based on the MAX31865 integrated circuit.  Features Two channels Compatible with 2-, ...

Pololu item #: 708 The Pololu dual high-power motor drivers are compact carriers for the VNH3SP30 and VNH2SP30 motor driver integrated circuits fr...

'easy-Radio' 433-4MHz FM transceiver with user programmable frequency, output power and data rate The embedded software converts user data, in ...

"easy-Radio" FM transceiver for European or USA markets. The embedded software converts user data, in most standard formats, and transmits over ...

This easy-Radio Explorer provides an USB connection to the PC. It is bus powered so no external PSU are required. The antenna connector is a standa...

This easy-Radio Explorer provides an USB connection to the PC. It is bus powered so no external PSU are required. The antenna connector is a standa...

sku: ROB-10267 The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to...

Looking to do more with your BBC micro:bit? Unlock its potential with this Edge Connector Breakout Board! This breakout board has been designed to ...

sku: WIG-10025 The EiBotBoard (EBB) was originally designed for the Egg-Bot project. It is a small (2.2" x 2.2") two channel stepper motor driver ...

Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20...

WRL-11395 We know what you're thinking, "What's the big deal? Looks like an SD card..." Well this is no SD card! The Electric Imp is a WiFi enabled...

BOB-11400  If you aren't familiar with the Electric Imp, it essentially provides an easy, integrated way to connect almost any hardware device both...

ELM327 v1.4 The ELM327 has been improved once again, with more error checking, code improvements, and of course, new features. Here are a few of t...

ELM327 v1.4b The ELM327 has been improved once again, with more error checking, code improvements, and of course, new features. Power Control ...

This is a CAN-Bus breakout board for the ELM327/9 IC. It provides an serial to OBDII data bridge for systems that uses the CAN-Bus protocol. Featu...

This is a multi protocol interface. It combines the ELM320, ELM322 and ELM323 into one IC, also adds CAN support (ISO 15765-4) as well. Sing...

This is a multi protocol interface. It combines the ELM320, ELM322 and ELM323 into one IC, also adds CAN support (ISO 15765-4) as well. Single...

The ELM329 is our CAN-only device that provides more CAN support than is in our popular ELM327. The current firmware adds several new features tha...

The ELM329 is our CAN-only device that provides more CAN support than is in our popular ELM327. The current firmware adds several new features tha...

Since 1996, most vehicles have been required to monitor their own emissions performance and to report on it through an On-Board Diagnostics (OBD) ...

sku: BOB-10402 This is a simple breakout board that uses a vertical SMD connector for the EM401 or EM406 GPS module cables. It features 4 mounti...

Empty OBDII connector and cable kit (include 16 pin) with PCB header board. USB cable with moulded strain relief. Cable length 2m. NOTE : This ki...

Enclosure Faceplate for ENC2015S enclosure and SBC66EC. This faceplate is meant to be used together with the SBC66EC board when mounted in one of ...

Enclosure faceplate (panel) for the PT24E when mounted in the ENC2015S enclosure. 

Enclosure for DMXDuino made from black anodised aluminium extruded box section. Front and rear panel from laser cut acrylic.Features Strong black ...

End plate in black anodized aluminium. Features  Size 108.5 x 45 x 1.5mm Black anodised Sold in single unit, two required per enclosure  Supplie...

End plate in black anodized aluminium. Features  Size 108.5 x 29.5 x 1.5mm Black anodised Sold in single unit, two required per enclosure  Supp...

End plate in silver anodized aluminium. Features  Size 108.5 x 29.5 x 1.5mm Silver anodised Sold in single unit, two required per enclosure  Sup...

End plate in silver anodized aluminium. Features  Size 108.5 x 45 x 1.5mm Silver anodised Sold in single unit, two required per enclosure  Suppl...